行业组件数据 · 2026

串联电感器

繁體:串聯電感器

串联电感器是电子电路中的一种基本无源元件,其电感量以亨利(H)为单位。它由绕在磁芯(空气、铁氧体或铁粉芯)上的导电线圈组成。当串联在电路中时,它通过自感特性阻碍电流变化,产生存储能量的磁场。在工业应用中,如输入匹配网络,它对于阻抗变换、滤除高频噪声以及确保射频和电力电子系统各级之间高效功率传输至关重要。

技术定义与适配语境
典型 串联电感器 会按材料、尺寸公差、适配关系和失效风险在 计算机、电子和光学产品制造 中评估。

串联电感器是电子电路中的一种基本无源元件,其电感量以亨利(H)为单位。它由绕在磁芯(空气、铁氧体或铁粉芯)上的导电线圈组成。当串联在电路中时,它通过自感特性阻碍电流变化,产生存储能量的磁场。在工业应用中,如输入匹配网络,它对于阻抗变换、滤除高频噪声以及确保射频和电力电子系统各级之间高效功率传输至关重要。 其工作原理基于法拉第电磁感应定律和楞次定律。当交流电(AC)流过电感器时,线圈周围产生变化的磁场,从而感应出阻碍电流变化的反电动势(EMF),产生感抗(XL = 2πfL,其中f为频率,L为电感)。在串联配置中,它充当频率相关的电阻,阻止高频信号通过,同时允许低频或直流电流通过,从而实现低通滤波和阻抗匹配等功能。

组件规格

定义
串联电感器是电子电路中的一种基本无源元件,其电感量以亨利(H)为单位。它由绕在磁芯(空气、铁氧体或铁粉芯)上的导电线圈组成。当串联在电路中时,它通过自感特性阻碍电流变化,产生存储能量的磁场。在工业应用中,如输入匹配网络,它对于阻抗变换、滤除高频噪声以及确保射频和电力电子系统各级之间高效功率传输至关重要。

其工作原理基于法拉第电磁感应定律和楞次定律。当交流电(AC)流过电感器时,线圈周围产生变化的磁场,从而感应出阻碍电流变化的反电动势(EMF),产生感抗(XL = 2πfL,其中f为频率,L为电感)。在串联配置中,它充当频率相关的电阻,阻止高频信号通过,同时允许低频或直流电流通过,从而实现低通滤波和阻抗匹配等功能。
工作原理
The working principle is based on Faraday's Law of Induction and Lenz's Law. When alternating current (AC) flows through the inductor, a changing magnetic field is generated around the coil. This induces a back electromotive force (EMF) that opposes the change in current, resulting in inductive reactance (XL = 2πfL, where f is frequency and L is inductance). In series configurations, it acts as a frequency-dependent resistor, blocking high-frequency signals while allowing low-frequency or DC currents to pass, enabling functions like low-pass filtering and impedance matching.
材料
绕组采用铜线或铝线磁芯材料包括空气(用于高频、低损耗应用)、铁氧体(用于高磁导率和高达MHz范围的频率稳定性)、铁粉芯(用于电力应用中高饱和磁通密度)或叠层硅钢(用于低频电力电感器)。导线涂覆绝缘材料如漆包线、聚酯或聚酰亚胺。封装可采用环氧树脂或热塑性外壳进行保护。
Q Factor
10 to 100 at specified frequency
Tolerance
±5% to ±20%
Current Rating
100 mA to 50 A
Inductance Range
1 nH to 100 mH
Saturation Current
Specified at 10-30% inductance drop
DC Resistance (DCR)
0.01 Ω to 10 Ω
Operating Temperature
-40°C to +125°C
Self-Resonant Frequency (SRF)
1 MHz to 1 GHz
标准
IEC 62368-1IEC 61558-1ISO 9001AEC-Q200

行业分类与别名

串联电感器 的常用贸易名称、技术标识和检索关键词。

上级产品

该组件会出现在以下整机或工业产品中。

FMEA · 风险与缓解

诱因 → 失效模式 → 工程缓解

Core saturation from exceeding current rating->Sudden drop in inductance, overheating, potential short circuit->Design with derating (use inductors rated at 150% of max operating current), implement current monitoring circuits, select cores with high saturation flux density
Poor soldering or mechanical stress->Intermittent or open connections, circuit malfunction->Follow IPC soldering standards, use strain relief in wiring, perform mechanical stress testing, apply conformal coating for protection
Operating at frequencies near SRF->Loss of inductive behavior, increased impedance unpredictability, circuit instability->Select inductors with SRF at least 10x above operating frequency, simulate circuit behavior, use network analyzers for verification

工业生态与工程逻辑

0
Overheating due to excessive current causing core saturation or insulation failure
1
Mechanical damage from vibration or shock leading to open windings
2
Parameter drift with temperature changes affecting circuit performance
3
Resonance issues if operating near SRF causing unexpected impedance behavior

合规与检测

tolerance
Inductance tolerance typically ±10% or ±20% per IEC standards; electrical isolation tested at 500V AC for 1 minute
test method
Inductance measured using LCR meter at specified frequency (e.g., 1 kHz for power inductors, 100 MHz for RF); DCR measured with four-wire ohmmeter; thermal cycling per IEC 60068-2-14

制造该组件的工厂

来自 CNFX 组件能力表的相关制造商资料。

制造商列表用于前期研究和供应商能力理解,不代表认证、排名或交易担保。

采购评估维度

不是客户评论,也不是实时热度。以下维度用于前期 RFQ 准备和供应商评估。

技术文档
4/5
制造能力
4/5
可检验性
5/5
供应商透明度
3/5

这些分值是采购评估维度示例,不代表真实客户评分、具体国家买家反馈或实时询盘。

相关组件

常见问题

What is the primary function of a series inductor in an Input Matching Network?

In an Input Matching Network, a series inductor is used to transform impedance between source and load, ensuring maximum power transfer by compensating for capacitive or resistive mismatches, and filtering out unwanted high-frequency noise.

How do I select the right series inductor for my application?

Consider key parameters: required inductance value, current rating (both RMS and saturation), frequency range (ensure SRF is above operating frequency), DCR for power loss, core material for frequency response, and physical size. Always refer to datasheets and application notes.

Can series inductors be used in DC circuits?

Yes, but they primarily affect AC components. In DC circuits, they act as short circuits (low resistance) to steady-state DC, while filtering AC ripples or transients, making them useful in power supply filters.

我可以直接联系工厂吗?

CNFX 是开放目录,不是交易平台或采购代理。工厂资料和表单用于帮助你准备直接沟通。

CNFX Industrial Component Index · 计算机、电子和光学产品制造

数据基础

CNFX 制造商资料、技术分类、公开产品信息和持续合理性检查。

初步技术归类
本页用于结构化准备研究、RFQ 和供应商评估,不替代买方自己的供应商资质审查、标准核验和技术批准。

请求制造能力信息: 串联电感器

说明目标数量、应用场景、交期和关键技术要求,用于准备 RFQ 或供应商评估。

谢谢,信息已发送。
谢谢,信息已收到。

需要制造 串联电感器?

对比具备该组件加工或装配能力的制造商资料。

创建制造商档案 联系我们
上一个组件
串口连接器
下一个组件
串行器(MUX)
URN:CNFX:ME:UNIT:SERIES_INDUCTOR